FOCUS On Transport and Logistics

Banner

 

You are here: Home Regulars Vic's View Understand your vehicles’ data plates
Banner
Banner
Banner

Understand your vehicles’ data plates

E-mail Print

Understand your vehicles’ data plates Commercial vehicle operators and drivers need to understand the information displayed on the data plate affixed to their vehicles. Without this information, it’s impossible to establish the maximum imposed load.

It is a mandatory requirement for all buses, minibuses, goods vehicles, truck tractors and trailers to display certain prescribed information, which must be clearly imprinted or stamped on a metal plate affixed in an accessible position. (Regulation 245 of the Road Traffic Act.)

The purpose of the data plate on a commercial vehicle is to indicate the various permissible and manufacturer’s maximum-load capacities of the vehicle. Failure to adhere to the maximum manufacturer’s specifications could result in the vehicle warranty being rejected and expensive repair costs.      

Failure to adhere to the legal limits could have very serious, costly and dangerous consequences, as well. Remember, ignorance of the law is no excuse.

The metal or aluminium plate must be affixed by the manufacturer of the vehicle; usually on the cab door or under the bonnet. On trailers it can normally be found in a visible position on the kerb side of the trailer.      

To understand these data plates it is necessary to understand the letter symbols shown on the plate. The information is divided into two sections. Normally the first section denotes the manufacturer’s specifications. The second section indicates the maximum permissible loadings, in other words the maximum legal mass of the loads.

The meanings of the symbols illustrated in the first section of a data plate are described below. These are the maximum design limits as set by the vehicle manufacturer.                            

GVM – Gross vehicle mass is the maximum total allowable mass that can be imposed on a vehicle, according to the manufacturers rating. This includes the mass of the chassis cab and the body.                                            

It also includes the payload and any add-on equipment that may be fitted to the vehicle. The GVM rating is set by the manufacturer and may not be exceeded.

GCM – Gross combination mass is the maximum total allowable mass that can be imposed on a vehicle when the vehicle is pulling a trailer.

Again, this includes the total mass of the truck, trailer(s), payload and any add-on equipment.

GA – Gross axle mass is the maximum load that the axle is designed to carry.

GAU – Gross axle unit mass is the maximum load that a tandem or tridem axle is designed to carry.

KW – the power rating of the vehicle in kilowatts.

T – Tare mass is the mass of the empty vehicle ready to travel on the road. This includes the body mass plus any add-on equipment, but excludes fuel and payload.

The meaning of the symbols illustrated in the second section of a data plate is described below. These are maximum legal limits set by the Department of Transport, taking into account the restrictions imposed by the Road Traffic Act. These limits must not be exceeded.

V – The maximum permissible (legal) mass, when fully loaded. This mass must not be exceeded when the vehicle is operating on a public road.

DT – Drawing vehicle’s maximum permissible mass.

A – Permissible axle mass load.

AU – Permissible axle unit mass load.

The information described on the plate allows the owner and driver of the vehicle to establish the exact payload that can be transported legally.

It is important to note that it is illegal for any of the information displayed on the plate to be altered in any way, without the consent and approval of the original manufacturer.

 


One of this country’s most respected commercial vehicle industry authorities, VIC OLIVER has been in this industry for over 50 years. Before joining the FOCUS team, he spent 15 years with Nissan Diesel (now UD Trucks), 11 years with Busaf and seven years with International.

 

Comments   

 
0 #1 Guest 2017-06-09 19:38
I bought a truck and registered it and everything was OK until at a weigh bridge they said the truck is overloaded - apparently the info on the data plate indicates it's a single-axle truck when it's a double-axle. The mistake was never picked up, how do I go about correcting it?
Quote
 

Add comment

Feel free to participate - we would love to have your opinion and input.


Security code
Refresh

Discover More About Focus

charmont media global Editrans - A Guide to Education in the Wheels Game Focus On Transport and Logistics is ABC Certified Focus On Transport and Logistics is an International Truck of the Year 2014 Associate Member

Truck Test 2017

Banner
Banner
Banner
Banner
Banner
Banner
Banner
  • Contact

  • Subscribe

  • Advertise

Enquiries and questions?Charmont Media Global
Unit 17 Northcliff Office Park
203 Beyers Naude Drive
Northcliff
Tel: 011 782 1070

Or complete the enquiry form »

Subscribe to FOCUS Contact our Circulation Manager to subscribe or click here to download the subscription form.

Bev Rogers
Tel: 011 782 1070
Cell: 078 230 5063
Email: bev@focusontransport.co.za

Be Seen! Advertise in FOCUSAdvertising Sales
Margaret Phillipson
Cell: 083 263 0451
Email: margaret@focusontransport.co.za

Atish Ramachul
Cell: 061 320 2210
Email: atish@charmont.co.za

Banner